OmahaNERecruiter Since 2001
the smart solution for Omaha jobs

Maintenance Tech Nights (Wed-Fri) Full-Time

Company: Drake-Williams Steel
Location: Omaha
Posted on: January 25, 2023

Job Description:

Job Details

Job Location
Structural - Omaha, NE

Position Type
Full Time

Salary Range
$25.00 - $32.00

Job Shift
2nd Shift [3:30 P.M.- 4 A.M.]

Description

Primary Purpose of this Position:

To maintain or repair DWS fabrication equipment, material handling equipment, buildings, facilities, and processes. Work on "projects" that improve the DWS processes. Make building and facility repairs.

Essential Job Functions:

  • PM machines based on PM procedures to help ensure machines run properly and efficiently.
  • Troubleshoot mechanical/electrical issues on equipment that is down.
  • Contact vendors for supplies and recommendations.
  • Input information into the Mega Mation tracking system.
  • Strategically visualize and communicate project plans and supplies needed.
  • Identify steel shapes, sizes, and mill tolerances for projects.
  • Operate overhead cranes, forklifts, jib cranes, gantry cranes, conveyors, machines, and transfers in order to PM or repair them.
  • Any other duties assigned by management (example- plow snow, sand lot, and grounds maintenance.
  • Attend all meetings as required by management.
  • Consistently and reliably works scheduled hours at assigned locations.

    FLSA Status: Non-Exempt

    Reporting Relationships:
  • Maintenance Manager
  • Support Services Director

    Qualifications

    Knowledge, Skills and Abilities:
  • Ability to read, write, and perform higher arithmetic computations involving addition, subtraction, multiplication, and division of whole numbers, decimals and fractions.
  • Ability to understand and carry out semi-complicated verbal and written instructions.
  • Ability to effectively communicate with vendors, co-workers, supervisors and managers.
  • Ability to work under periodic supervision focused on the progress of work and setting priorities for job completion.
  • Skill in using tape measure, or other measuring devices.
  • Ability to pass a Drake-Williams Steel, Inc. administered test that covers shop drawing interpretation, fractional number calculations, basic geometry, etc.
  • Ability to interpret shop drawings for projects.
  • Ability to possess pride in own workmanship, demonstrate attention to detail, and work safely.
  • Ability to operate forklifts and overhead cranes in a safe and proper manner. Use and understand industry and Drake-Williams Steel adopted hand signals used for crane operations.
  • Perform minor/major mechanical tasks on machines.
  • Ability to multi-task.

    Physical Demands:
  • Stand OCCASIONALLY to FREQUENTLY over the course of the 8 to 12 hour work shift depending on needs.
  • Walk OCCASIONALLY to FREQUENTLY over the course of the 8 to 12 hour work shift.
  • Sit OCCASIONALLY during break, lunch periods, and to input data.
  • Lift weights up to 25 pounds FREQUENTLY from floor to waist, which includes the various tools, chains, valves, and various components during the 8 to 12 hour work shift.
  • Lift weights up to 100 pounds OCCASIONALLY from floor to waist, which includes the various motors and components during installation or removal during the 8 to 12 hour work shift.
  • Carry 100 pound weight noted above distances up to 10 feet. Lighter weights may be carried up to several hundred feet depending on job location.
  • Climb OCCASIONALLY to FREQUENTLY up and down steps, ladders, onto material, or onto conveyors depending on job location.
  • Balance OCCASIONALLY while working on machinery and climbing into and out of the manlift.
  • Bend OCCASIONALLY depending on task location while removing tools, components, etc.
  • Stoop or crouch OCCASIONALLY while performing the regular job duties. The position will be held continuously for a few seconds to 15 minutes, depending upon the job.
  • Kneel in the commission of job duties OCCASIONALLY, depending upon the job.
  • Crawl OCCASIONALLY up to 15 feet to access tools, materials, etc.
  • Reach forward FREQUENTLY to perform job duties or to retrieve tools. The employee will OCCASIONALLY be required to reach to full forward extension.
  • Reach overhead OCCASIONALLY to FREQUENTLY to work on forklifts, cranes, machines, building, etc.
  • Push and pull material OCCASIONALLY to FREQUENTLY with force of up to 50 pounds. The distance may be from a few feet to several hundred feet while pushing parts on the worktable or pushing a paint pump.
  • Pull hand over hand OCCASIONALLY to FREQUENTLY to pull chain through material. Force varies up to 70 pounds.
  • Gross finger dexterity skills required to operate the various tools and equipment utilized in the course of standard job duties.
  • Fine finger dexterity skills required to operate the various tools and equipment utilized in the course of standard job duties.

  • Non-Material Handling Demands
  • Employee is expected to work 40 hours a week. However, hours including overtime and weekends may be required based on Drake-Williams Steel's needs.
  • Hear sufficiently to be aware of safety issues
  • Visual ability to read and interpret schematics, manuals, etc. Safety glasses are required in the shop area.
  • Exposure to heat, cold, wet and humid conditions inside and/or outside of the facilities OCCASIONALLY.
  • Exposure to fumes, odors and dusts in the shop area OCCASIONALLY.
  • Exposure to solvents, greases, oils, and coolants OCCASIONALLY.
  • Wear all required Personal Protective Equipment. PPE includes steel-toe safety shoes, hearing protection, safety glasses, gloves, and hard hats.
  • Work at heights that may range up to 40 feet.

    Tools Required:

    Pencil, Tape Measure, Markers, Chainsaw, Grab Hooks, Pry-Bar, Ladders, Remote Control, Wrenches, Hammers, Drills, Chains, Electrical Test Equipment, etc.

    Machines Utilized:

    Overhead Crane, Jib Crane, Gantry Crane, Transfers, Fabrication Process Equipment, Computers, Tractors, Mobile Yard Crane, Snow Plow/Sander, Manlift, and Forklifts.

    Experience and Education Required:
  • High School degree or equivalent.
  • Minimum of six months of experience in a steel manufacturing environment.

    Please visit our Employee Benefits page for more information!

Keywords: Drake-Williams Steel, Omaha , Maintenance Tech Nights (Wed-Fri) Full-Time, Professions , Omaha, Nebraska

Click here to apply!

Didn't find what you're looking for? Search again!

I'm looking for
in category
within


Log In or Create An Account

Get the latest Nebraska jobs by following @recnetNE on Twitter!

Omaha RSS job feeds